Auxiliary Lathe Tool Rest

Auxiliary Lathe Tool Rest Turning

Auxiliary lathe tool rest is post about Turning bookmarked by luis with ID 13287235275 was uploaded on 30-03-2019 and has been viewed 310,852 times.

My lathe has a 15-in.capacity over the gap, but when I mount a large bowl or tray, it's impossible to get the tool rest behind the blank to turn the bottom.To provide a tool rest for working the back, I bent a str*p of 3/8 in.

-thick iron to a 90¡ angle and bolted it to my headstock casting, as shown in the sketch.The tool rest was so useful that I made a set of them bent to different angles to fit different shapes.For safety's sake, remove the tool rest before sanding so your fingers don't get pinched...

Read More →

Disclaimer: images, articles or videos on this website sometimes come from various other media sources. Copyright is fully held by the source. If there are problems related to this, you can contact us on this page.
Bookmark ID: 13287235275

Auxiliary lathe tool rest is just one of the many collections of bookmark on this website. There are approximately 898 posts that exist in our database associated with this article. Here are the details of "auxiliary lathe tool rest" article:

Category:
Title:
Image URL:
Post URL:

This is a article related to auxiliary lathe tool rest, there are approximately 898 post related to this turning category. Please see the details below and click on the title for more information..

Auxiliary Lathe Tool Rest Turning 150 x 100

Auxiliary Lathe Tool Rest

My lathe has a 15-in.capacity over the gap, but when I mount a large bowl or tray, it's impossible to get the tool rest behind the blank to turn the bottom.To provide a tool rest for working the back, I bent a str*p of 3/8 in.-thick iron to a 90¡ ... Auxiliary lathe tool rest is bookmark about Turning bookmarked by tommy with ID 13287235275 was uploaded on 30-03-2019 and has been viewed 310,852 times.

Adjustable Tool Rest Accessories 150 x 100

Adjustable Tool Rest

Here is an adjustable bench-grinder tool rest that's accurate, easy to use and cheap to build.Cut a 1-1/2-in.thick pine hinge-block at the angles shown and mount it to the base with screws from underneath.Cut down two Stanley 10-in.lid supports to make the table-adjusting hardware.Drill out the center rivets and replace ... Adjustable tool rest is post about Accessories bookmarked by russell with ID 1497729741 was uploaded on 08-01-2019 and has been viewed 214,226 times.

Tool Review Turbo T40 Lathe By Harvey Machinery 150 x 100

Tool Review Turbo T40 Lathe By Harvey

Let's talk about what makes a good wood lathe: a cast-iron bed, strong cam locks for fastening the banjo and tailstock, good torque, common spindle thread dimensions, easy belt changes, easy spindle lock, forward and reverse capability, and responsive speed adjustments.The Harvey Turbo T40 has all of these.And it fits ... Tool review turbo t40 lathe by harvey is bookmark about Machinery bookmarked by jason with ID 14243595248 was uploaded on 12-03-2019 and has been viewed 92,334 times.

Lathe Steady Rest Turning 150 x 100
Lathe Steady Rest

This shopmade steady rest can be set up to support the middle of a long, thin spindle, or it can be used as a tailstock for center-boring.Derived from a metalworkers' steady, the rest consists of a rigid plywood upright, three adjustable hardwood bearing blocks, and a base that locks in ... Lathe steady rest is bookmark about Turning bookmarked by harvey with ID 12231261270 was uploaded on 22-01-2019 and has been viewed 271,199 times.

Swing Arm Lathe Tool Holder Project Plans 150 x 100
Swing Arm Lathe Tool Holder

Build the holder as shown or customize it to fit your tool needs.Either way, it keeps your lathe tools and accessories close at hand.Now, if only hollowing a bowl were this easy Swing arm lathe tool holder is article about Project Plans bookmarked by sidney with ID 14104644951 was uploaded on 11-01-2019 and has been viewed 429,321 times.

Easy Access Lathe Tool Rack Project Plans 150 x 100

Easy Access Lathe Tool Rack

With the look of a fine gun rack, this storage unit keeps long-handled turning tools in a secure horizontal display Easy access lathe tool rack is bookmark about Project Plans bookmarked by clinton with ID 13219263425 was uploaded on 10-02-2019 and has been viewed 12,631 times.

Ever Ready Lathe Tool Holder Project Plans 150 x 100

Ever Ready Lathe Tool Holder

This quick-to-make project slides between the rails in the lathe bed (known as the ways) and cradles turning tools within arm's reach.When not in use, it hangs on the wall out of the way.Feel free to customize it for the number and types of turning tools you own Ever ready lathe tool holder is article about Project Plans bookmarked by gary with ID 11008560190 was uploaded on 09-01-2019 and has been viewed 92,636 times.

Self Cleaning Lathe Tool Storage Shop Tips 150 x 100

Self Cleaning Lathe Tool Storage

I like to have my lathe tools close at hand, so I found a way to mount 12"-wide wire closet shelving to my lathe stand Self cleaning lathe tool storage is post about Shop Tips bookmarked by carl with ID 13268245039 was uploaded on 09-02-2019 and has been viewed 162,465 times.

Cut Kerfs For Easy Tool Rest Adjustment Shop Tips 150 x 100

Cut Kerfs For Easy Tool Rest Adjustment

When turning, almost every tool change requires resetting a lathe's tool-rest height Cut kerfs for easy tool rest adjustment is bookmark about Shop Tips bookmarked by steve with ID 1929356134 was uploaded on 25-03-2019 and has been viewed 278,279 times.

Self Cleaning Lathe Tool Storage Woodworking How To 150 x 100
Self Cleaning Lathe Tool Storage

Wood shaving and lathes go hand in hand, but your turning tools don't need to be part of the mess with this "off-the-shelf" solution Self cleaning lathe tool storage is bookmark about Woodworking How To bookmarked by tracy with ID 12643111790 was uploaded on 06-04-2019 and has been viewed 162,465 times.

Turning Project In This Article I Describe Turning A Piece Of Wood That Is Not Round And Retains Its Square Corners When The Piece Is Turning At High Speed The Corners Become Invisible So I Always Keep Firmly In Mind That The Only Thing Allowed To Extend Past The Tool Rest Is The Tool It Is Even More Important Than Usual To Stop The Lathe Before Moving The Tool Rest And To Rotate The Piece By Hand To Ensure It Is Clearing The Tool Rest Before Switching The Lathe On Magazine 150 x 100
Turning Project In This Article I Describe Turning A Piece ...

Candle Holders Most faceplate turning projects only require that you have one flat face on the blank for resting on the band saw table while trimming it round, and for attaching the faceplate or chuck.However, for this project it is important that you mill the stock for the blanks exactly ... Turning project in this article i describe turning a piece of wood that is not round and retains its square corners when the piece is turning at high speed the corners become invisible so i always keep firmly in mind that the only thing allowed to extend past the tool rest is the tool it is even more important than usual to stop the lathe before moving the tool rest and to rotate the piece by hand to ensure it is clearing the tool rest before switching the lathe on is article about Magazine bookmarked by stephen with ID 13522847299 was uploaded on 16-02-2019 and has been viewed 243,055 times.