Drilling Centered Holes In Spheres

Drilling Centered Holes In Spheres Woodturning Projects

Drilling centered holes in spheres is article about Woodturning Projects bookmarked by marvin with ID 13813271781 was uploaded on 08-04-2019 and has been viewed 382,327 times.

In my high-school woodshop class, we needed to drill 1/2-in.-dia.holes partway through 100 1-1/4-in.-dia.hardwood balls.I suggested to the instructor that we clamp a board to the drill press table and bore a 3/4-in.

-dia.hole in the board to serve as a socket to hold the ball being drilled.Then we chucked a 1/2-in.-dia.Forstner bit into the drill press and set the stop to the desired depth.One student held each ball while another drilled.

Each hole was perfectly centered.This technique worked so well that my instructor suggested that I submit it to the Methods of Work column.Many of the methods shared by readers of Fine Woodworking have been put to good use in our shop and I hope that this idea may be useful to another woodworker...

Read More →

Disclaimer: images, articles or videos on this website sometimes come from various other media sources. Copyright is fully held by the source. If there are problems related to this, you can contact us on this page.
Bookmark ID: 13813271781

Drilling centered holes in spheres is just one of the many collections of bookmark on this website. There are approximately 1026 posts that exist in our database associated with this article. Here are the details of "drilling centered holes in spheres" article:

Category:
Title:
Image URL:
Post URL:

This is a article related to drilling centered holes in spheres, there are approximately 1026 post related to this woodturning projects category. Please see the details below and click on the title for more information..

Drilling Centered Holes In Spheres Woodturning Projects 150 x 100

Drilling Centered Holes In Spheres

In my high-school woodshop class, we needed to drill 1/2-in.-dia.holes partway through 100 1-1/4-in.-dia.hardwood balls.I suggested to the instructor that we clamp a board to the drill press table and bore a 3/4-in.-dia.hole in the board to serve as a socket to hold the ball being drilled.Then we chucked a ... Drilling centered holes in spheres is article about Woodturning Projects bookmarked by nathaniel with ID 13813271781 was uploaded on 08-04-2019 and has been viewed 382,327 times.

Cut Slotted Scr*W Holes In A Drawer Bottom Construction 150 x 100

Cut Slotted Scr*W Holes In A Drawer Bottom

I like the chamfered scr*w slots found on the bottoms of many drawers.What's a good way to make them? Cut slotted scr*w holes in a drawer bottom is post about Construction bookmarked by luis with ID 1981461648 was uploaded on 22-03-2019 and has been viewed 234,747 times.

Drilling Angled Holes Construction 150 x 100

Drilling Angled Holes

For my early American reproductions, such as cobbler's benches and step tables, I have found that splaying the legs about 5¡ in two directions is just about right Drilling angled holes is article about Construction bookmarked by kelly with ID 1373496169 was uploaded on 01-03-2019 and has been viewed 227,669 times.

Drilling Pin Holes In Mortise And Tenon Joints Joinery 150 x 100
Drilling Pin Holes In Mortise And Tenon Joints

To pin mortise-and-tenon joints in a table frame, lay out the mortise location on a piece of 3/4-in.scrap the width of the table leg.Then drill two holes using the drill press at the desired pin locations.Now position this jig on the table leg flush with the top, and clamp and ... Drilling pin holes in mortise and tenon joints is article about Joinery bookmarked by edward with ID 1719345674 was uploaded on 08-02-2019 and has been viewed 315,556 times.

Drilling Cribbage Board Holes Uncategorized 150 x 100
Drilling Cribbage Board Holes

Drilling holes in a cribbage board is time-consuming and very exacting.The fixture shown here produces fast, accurate holes by using small spacers to locate them.Four thin spacers are used for the holes within each group of five, and every fifth spacer is thicker, to set the wider areas between the ... Drilling cribbage board holes is post about Uncategorized bookmarked by jorge with ID 12431419813 was uploaded on 04-04-2019 and has been viewed 282,169 times.

Drilling Long Holes With Gun Drills Woodworking Jigs 150 x 100

Drilling Long Holes With Gun Drills

Chris Becksvoort's answer to the long-hole end-grain drilling question (Fine Woodworking #116, p.26) is right on target for woodworkers who do this occasionally.But if you are doing production drilling of long holes, a gun drill is the way to go.Gun drills are special bits made for drilling steel gun barrels.They ... Drilling long holes with gun drills is article about Woodworking Jigs bookmarked by edward with ID 1382746103 was uploaded on 28-03-2019 and has been viewed 102,418 times.

Drilling Deep Holes On The Lathe Woodworking Jigs 150 x 100

Drilling Deep Holes On The Lathe

As a maker of traditional wooden fifes, I need to bore long, straight holes in the ends of my flutes.I do this operation on a lathe using an end-boring jig I made from metal pipe and scrap iron.The tool is adapted from a method described to me by Trevor Robinson, ... Drilling deep holes on the lathe is article about Woodworking Jigs bookmarked by fernando with ID 12064704028 was uploaded on 26-02-2019 and has been viewed 325,411 times.

Enlarge Holes In Two Easy Steps Shop Tips 150 x 100

Enlarge Holes In Two Easy Steps

Maybe you need to enlarge a hole, or make a dead-on round hole larger than your largest Forstner bit Enlarge holes in two easy steps is bookmark about Shop Tips bookmarked by tyler with ID 12138547651 was uploaded on 20-03-2019 and has been viewed 125,840 times.

Locate Shelf Pin Holes In A Snap Shop Tips 150 x 100

Locate Shelf Pin Holes In A Snap

When I build shelves, I want them adjustable, and the most effective way to do that is with shelf pins Locate shelf pin holes in a snap is bookmark about Shop Tips bookmarked by jack with ID 12535043939 was uploaded on 09-04-2019 and has been viewed 401,709 times.

Drilling Shelf Support Holes Tools And Reviews 150 x 100
Drilling Shelf Support Holes

WOOD Magazine Projects Editor Jan Svec demonstrates four easy and inexpensive methods for drilling evenly-spaced, perfectly-aligned shelf support holes for adjustable shelves Drilling shelf support holes is article about Tools And Reviews bookmarked by martin with ID 14270183354 was uploaded on 26-02-2019 and has been viewed 119,320 times.

Sighting In On Centered Spindle Holes Woodworking How To 150 x 100
Sighting In On Centered Spindle Holes

To align the legs on a set of bunk beds, I came up with this method to precisely center a hole using a laser bore sighter for rifles Sighting in on centered spindle holes is post about Woodworking How To bookmarked by dale with ID 12527801735 was uploaded on 24-01-2019 and has been viewed 336,640 times.