How To Build A Chessboard
How to build a chessboard is article about Woodworking bookmarked by claude with ID 14252122144 was uploaded on 27-02-2019 and has been viewed 35,801 times.
Materials List8' 1x4 Board of Dark Wood (Mahogany)8' 1x4 Board of Light Wood (Aspen)2' x 2' of 1/2' PlywoodWood Glue1' 18-Gauge Brad NailsWhat It TakesTime: 3 hoursCost: $30Skill Level: IntermediateTools: Table Saw, Miter Saw, 18-Gauge Brad Nail Gun, Router, ClampsRip Boards on Table SawRip boards to 1-1/2 in.
on the table saw.You can certainly buy 1x2 boards and skip this step, but I don't always trust the edges to be perfectly square.Rough Cut Boards with Miter SawCut four pieces from each ripped wood species to a rough 16 in.
We used a stop so we didn't need to measure over and over again.This rough cut will give you a little leeway when you glue up the pieces and when you cut them into strips.Glue Up the StripsLay out the boards alternating light and dark wood.
Make sure the edges fit together well.In other words, don't rely on the clamps to squeeze the boards together.Spread the wood glue on the boards, making sure to get it even and all the way to the edges.
Clamp together with bar clamps.Let dry completely.Plane or Sand the BoardPlane or sand with a low-grit sandpaper to get the newly created board flat and even.Cut Off the Rough EdgesUse a miter gauge on the table saw to cut off the rough edges of the board.
Set a Stop & Crosscut the BoardUsing the same miter gauge method as above, set up a stop at 1-1/2 in.from the blade and crosscut eight strips from the board.Flip the Strips & Glue UpLay out the strips and flip every other strip, creating the chessboard pattern.
Glue up the strips and clamp them together.Let dry completely.Sand or plane the newly created chessboard.Cut Plywood & Fasten to ChessboardMeasure the dimensions of the chessboard.It's fairly unlikely that it will be perfectly square, but just make sure.
Rip and crosscut your 1/2 in.plywood to the size of your chessboard.Using glue, clamps and 1-in.18-gauge brad nails, fasten the plywood to the chessboard to create a flat surface on the bottom.Rip Wood to DepthMeasure the height of the chessboard at several points, take the smallest height, and rip the lighter wood species to that size.
Scribe Lengths of WoodLine up the ripped light board with the chessboard and scribe the lengths.Cut the light wood board to those lengths on the miter saw.Using glue and brad nails, fasten the pieces to the edges of the chessboard.
Sand until the chessboard is flush with the outer frame.Round Over & Rip Darker WoodUse a router and a 1/4-in.round-over bit to round the edges of the dark wood.Rip the board to 3/4 in.on the table saw.
If you don't want to do this step, home stores sell 3/4-in.quarter-round moulding of nearly every species of wood.These materials are usually pretty cheap and can save you some building time.Miter Angles Into Rounded Board for the Outer EdgeMiter a 45-degree angle into the rounded board.
Take it to the chessboard and scribe the other side of the board to get the length of the outer rim.Repeat this process to get the other three sides.Glue & ClampGlue and clamp the mitered boards to the chessboard and let it sit until it's fully cured.
Make sure to spread the glue onto the angles.This is key to a good hold.If you don't trust just the glue, you can also nail 1-1/2-in.18-gauge brad nails into the chessboard and make it completely secure.