2 Hour Project How To Build A Cantina Bird Feeder
2 hour project how to build a cantina bird feeder is article about Woodworking bookmarked by thomas with ID 1171393827 was uploaded on 11-02-2019 and has been viewed 32,749 times.
Build this bird feeder from standard pine boards or from pressure treated lumber.Treated boards will give you long-term rot resistance, but also have a disadvantage: Treated lumber contains a lot of moisture, so you'll have to let it dry for at least two weeks before painting it.
Treated lumber also tends to cup or bow as it dries.Either type of lumber will contain knots.If you don't like the knotty look, buy an extra board or two so you can use the knot-free sections.You can use just about any wine or liquor bottle for this project.
Photo 1 and 4 show you how to customize the parts to suit your bottle.And you can use any drink glass that has a flat base.Securing the bottle in the feeder is very important.No matter how you display the project, something as simple as wind and rain can alter the bottle enough to knock it out of its perch and spill a lot of bird feed or break glass all over the ground.
We used 3/8 in.adhesive-backed rubber weatherstrip placed on the inside of both braces (part F) to secure the bottle.You can find this product in the hardware section in most home centers and online.Below is the complete list of what you will need to buy at your local home center and liquor store.
Materials3' 1 x 8 Board (1)6' 1 x 4 Board (1)2' 3/8' Dowel (1)Liquor/Wine BottleGlassBottle Caps (4)Mirror Clips (3)3/8' Adhesive-Backed Rubber Weatherstrip1-1/2' Trim Head Screws (20)5-Gallon BucketHot GlueToolsJigsawDrill/DriverClampsSpeed SquareHot Glue GunUtility KnifeCutting ListCut the sidesAngle your jigsaw to 45 degrees and cut the sides (part C) to the heights of your bottle and glass added together and then subtract 2 in.
Ours ended up being about 15 in., but this will almost certainly be different for your project so plan accordingly.Make the keyhole for the bottleCut a circle with a 2-1/2-in.hole saw in the center of the bottle holder board (part B).
Then, use your jigsaw and square to create a 1-1/2-in.wide channel that will fit the neck of your bottle.Fasten the sides to the baseUse a scrap piece of wood as a guide and scr*w the sides 3/4 in.from the edges of the base.
Attach the bottle holder to the sidesMockup the assembly to find the correct height of the bottle holder (part B).Cut some scrap wood to hold up the bottle holder to the correct height so it stays level.
Drill pilot holes and scr*w into the bottle holder from the outside of the feeder.Mount the roofScrew the longer roof piece (part D) to one end of the shorter roof piece (part E) and attach the roof to the tops of the sides with screws.
Be sure to drill pilot holes so that you know the screws will keep the roof in line.Create and attach the bracesCut the 1x4 pine to 10 in.pieces.Miter a 45-degree angle into the ends, leaving 3/4 in.on the ends.
Mark 3/4 in.from the edges and use a 5-gallon bucket to mark an arc on the board.Clamp the board to the work surface and cut the arc with a jigsaw.Screw the braces to the sides.Cut the adhesive-backed rubber weatherstrip to 3 in.
with a utility knife.Peel the backing and attach the strips to the inside of the braces.Attach the mirror clips to the base of the feederMark a centerline on the base.Set your glass onto the center of the base and scr*w the mirror clips to the base, securing the glass to the assembly.
Put in the bar stoolsCut your dowel to 4 in.pieces.Plan out where you want the bar stools and drill 1/4-in.-deep pilot holes with a 3/8-in.drill bit into the base.Create an 'L' guide with scrap 1x4 to make sure you drill plumb into the base.
Hot glue the bottle caps to the top of the dowels to create the final bar stool look.Once you you finish, you can paint/finish the bird feeder anyway you would like.We went a little crazy and tried to keep the cantina style with our paint styling.
We used some basic acrylic paints and primer that you can purchase at any craft store.Tech Art...