Built To Last Viking Long Table

Built To Last Viking Long Table Woodworking

Built to last viking long table is post about Woodworking bookmarked by isaac with ID 12595669567 was uploaded on 29-01-2019 and has been viewed 253,520 times.

The Viking TableThis style of viking table is known as a drawbore trestle.The 'trestle' is the stretcher that connects the legs, and 'drawbore' refers to the 'bored' mortises and tenons that 'draw' the legs and trestle tightly together to create a stable base.

You can easily shorten (and lighten) your table by modifying the dimensions given.The benches that accompany this table are built using the same template and same basic procedures.Check out the heavy-duty viking bench project directions here.

If you're thinking of building both the table and the bench, consider starting with the bench; it's a great warm-up for the larger viking table project.Or check out our top 10 woodworking projects.It's "Knockdowable"!The viking table, built as shown, is enormous— long, wide and weighty.

But by removing two wedges and eight screws, you can separate the legs, tabletop and trestle so you can store the table for the winter or move it to a different location.Pick the right woodIf you're building this viking table for inside use, you can use everyday dimensional lumber or more expensive hardwoods.

But if it will be used outside, consider one of the following weather-resistant options:Cedar, Redwood or CypressOne of these 'premium' exterior woods is most likely available in your area.Select boards with the most heartwood— the darker inside part of the tree, which is more durable than the lighter colored sapwood.

The downside? These woods can be wickedly expensive and, in some cases, soft.Treated LumberIt's moderately priced and stands up well to weather, but it's often wet from the treatment process, which means it's more likely to shrink and twist, and less likely to glue up well.

It's also difficult to apply a good-looking finish until the wood fully dries.Douglas FirThis is the wood we used.It's more expensive than the more widely available 'standard' dimensional lumber—often labeled H-F, S-P-F or 'white wood'—but cheaper than the premium woods.

It's about 20 percent harder, and stronger, heavier and more moisture resistant than standard lumber.Not all home centers and lumberyards stock Douglas fir; look for the 'Doug Fir' or 'DF' stamp.If in doubt, ask.

In our area, Lowe's and contractor lumberyards carry Douglas fir.White OakWe used white oak for the feet, the breadboard ends and the wedges.Other woods would work fine, but we liked the extra strength, hardness and contrast the white oak provided in these critical pieces.

Red oak, the type you'll often find at home centers, isn't a good substitute, since it's much more prone to rot.You can find white oak at specialty woodworking stores and online.Project Directions:Douglass fir tables are extremely durable, and after four years all we had to do was give it a quick sanding and a coat of Cabot Australian Timber Oil every spring and cover it with a tarp during the tough Minnesota winters.

The table remains as beautiful as it was on the day it was made.Take your time at the lumberyard (check out our lumber yard guide) selecting flat, straight boards free of split ends, twists, cupping and loose knots—you'll spare yourself a lot of clamping and cussing down the road.

If you have trouble finding perfect 2x12s, purchase an extra board—or longer boards and cut around the defects.Cut your boards into eight 22-in.-long pieces; make sure the ends are square.Pair up your boards so when one is laid atop the other, there's little or no gap along the ends and edges.

If you flip or rotate the boards, sometimes you'll find the perfect fit.Try to have any defects fall in the areas of the wood you'll be cutting away as you form the legs.Make the Leg TemplateMark out your leg template onto 1/4-in.

plywood as shown above.Set another scrap piece of plywood against the template.Drive a scr*w 9-1/4 in.from the end of the scrap and use that scr*w as a pivot point for your tape measure.Then swing the two arcs to create the leg shape.

Cut just outside the line with a finetooth jigsaw blade, then use a belt sander to sand right up to the line.Use your template to trace the leg shape onto two leg sections, which breaks down to eight separate leg pieces (Labeled "A", in Figure B in Project PDF's below).

10 DIY Tables You Can Build QuicklyGlue up the Leg "Sandwhich"Trace the leg shape onto two 22-in.2x12s, lightly dampen the bottom piece—polyurethane glue needs moisture to work— then apply healthy squiggles of the glue across the main body of the leg.

Use a plastic putty knife to spread the glue slightly beyond the edges of the layout lines and across the main body of the leg.12 Crafty Ideas for DIY Table CenterpiecesClamp the Leg Blanks TogetherPlace the top board over your glued board, taking care to even up the edges.

Install two or three screws in the waste area to keep the pieces aligned and then use clamps— lots of them—along all the edges.Drive additional screws into the waste area to help draw the pieces tightly together.

The glue will foam as it goes to work.Keep your boards clamped together at least two hours or overnight for good measure.Create three more leg blanks this way.14 Super Cool Homemade Coffee Table IdeasCut the Legs to ShapeCut out the legs.

A jigsaw with a long, coarse blade works fine, but a band saw works better, so use one if you have access to it.Whichever tool you use, make a series of 'relief' cuts as shown.These allow you to remove waste material as you cut.

They also allow your blade to get back on track if it wanders and begins making angled cuts, which jigsaws in particular are prone to do.If you have a jigsaw with reciprocating action, set it at zero; it will cut slower, but your blade will wander less.

Build a Router Table by Upcycling a Kitchen CountertopSand the Legs and Rout the EdgesNext use a belt sander to smooth and true up the curved sides.Clamp the legs to your work surface.Begin with a coarse belt, then progress to finer grits.

If you have access to a bench top belt sander or spindle sander, use it; you'll get results faster.Use a router with a 1/2-in.round over bit to soften the edges of the curved parts.Don't rout the tops and bottoms of the legs or the flat area where the mortise cutout will be.

DIY Table Saw TableCreate the Leg AssembliesPosition two leg sections next to each other and check to make sure the mortise cutout (where the stretcher tenon will go) can accommodate a 2x6 test piece.It's easier to enlarge these areas now, before joining the legs.

Set the legs on 1/4-in.spacers (so they'll be centered on the 2x4 top and bottom plates).Then apply construction adhesive to the ends to add a layer of moisture protection, and cinch the leg sections tightly together and to the 2x4 plates (B, C) with clamps.

Secure the legs to the plates using 3-1/2-in.exterior screws.Repeat for the other leg assembly.Cut the feet (D) to size and shape, then secure them with glue and screws to the bottom plates.How to Use a Table Saw: Ripping Boards SafelyCut the TonguesThe 2-1/4-in.

-wide boards along the long edges give the tabletop more mass to match the heft of the legs.Rip your two 2-1/4-in.-wide edge boards (F) from a 2x6.Cut these and your four 2x10 top boards (E) to length.

To create the 'tongues' that slide into the breadboard ends, set your circular saw to cut 3/4 in.deep, then make one cut 3/4 in.from each end of each board, another cut right along the end, and then a couple more cuts in between.

Place your chisel along the end cut and use it as a guide to remove the waste material.When you're done, each end will have a 3/4-in.x 3/4-in.tongue.Make the same cuts on the top and bottom of the edge boards (F) as shown.

Be sure to position the top and edge boards good side up.5 Must-Have Table Saw Accessories for Your Home WorkshopBuild the Breadboard EndsNext, make your board ends (H, J) as shown above; they're essentially three-board sandwiches with the middle board inset 3/4 in.

to accommodate the tongues you've created.We made ours from white oak for strength, appearance and durability, but you can make yours from the same wood as your table.Be sure to use waterproof glue.Rout the outer edges and cut the breadboard ends to length; make them 1/2 in.

longer than the width of the finished tabletop to accommodate board movement.'Breadboard' ends have been used by woodworkers for centuries—and for good reason:• They help keep the ends of the tabletop boards flat and aligned.

• They help protect the end grain of the boards from moisture and wear.• They allow the top boards to shrink and expand more freely without cracking.• They provide a smooth edge for your tummy to rest against.

How to Build a Drill Press TableAssemble the TopPlace your two edge boards (F) and four tabletop boards (E) on your work surface upside down.Space your top boards 1/8 in.apart using drywall nails or shims.

Even up the ends of the six boards, then tap the breadboard ends into place.Position the braces (G) and make sure everything is tight and square.Then drill 3/8-in.- diameter holes through the support braces and secure the braces to the four tabletop boards using 1/4-in.

x 2-1/2-in.washer-head screws.Note: The slightly oversize holes give the boards wiggle room to shrink and expand to help prevent cracking.Pre-drill holes in the breadboard ends—one centered on each of the four wide boards—and secure them with 3-1/2-in.

washer-head screws.Finally, drill holes along the center of the edge boards (F); angle them slightly toward the top of the table so the screws will have plenty of meat to bite into, then drive home the 3-1/2-in.

washer-head screws.How to Build a Welding TableTake Measurements for the StretcherPosition the two leg assemblies as shown above.Make sure they're square to the tabletop, then measure the distance between them.

This will give you the dimensions you need to create your stretcher.Note that we provide an exact stretcher length in the Cutting List (in Project PDF's below), but your length will most likely differ.

There are a few key measurements you need to get right in order for your stretcher and drawbore wedges to do their jobs.The shoulder measurement.This is the distance between leg assemblies.This distance is key because the shoulders hold the leg assemblies the right distance apart and 'wiggle-proof' the table.

The tenon length and width.The tenon extends 7 in.past the shoulder and should be 5-1/2 in.wide.The mortise cutout.The cutout is centered on the tenon and is 5/8 in.wide and 2-1/2 in.long.The edge of the mortise near the outside of the leg should be inset into the leg by about 1/8 in.

so that when the wedge is installed, it will draw the shoulder tightly against the leg.When done properly, this joint is amazingly strong, so take your time to get it sized and positioned just right.Table Saw Tips and TricksLayout and Cut the StretcherWith all of this in mind, make the stretcher.

Once you've marked the key stretcher length, tenon and mortise measurements, bend a thin piece of wood to create the arched bottom of the stretcher.Use a jigsaw to cut out the parts.Drill 5/8-in.starter holes in each end of the 2-1/2-in.

-long mortises to give your jigsaw an entry point.Table Saw Tips and TechniquesInstall the Stretcher and Wedge it TightTo make your wedges (L), first cut a 3/4-in.board 24 in.long, then rip it 2-1/4 in.

wide.Use a belt sander to taper each end of the board, then cut them to their final 7-in.length and soften the edges.Separate the legs and install the stretcher.Drive the wedges into place as shown above.

The scr*w driven through the end of the tenon helps reinforce it to prevent the wedge from blowing out the end of the tenon when driven in tightly.13 Dirt-Simple Woodworking Jigs You NeedScrew the Leg Assemblies to the BracesOnce the stretcher and legs are locked together, secure the leg assemblies to the tabletop crosspieces (Photo above).

Center the leg assemblies on the end braces.Drill oversize holes through the leg plates, then secure the legs to the top with washer-head screws.Stone-Top Patio TableFinishing UpSand and smooth out any rough areas, then apply your exterior finish.

You now have a beautifully built viking table!How to Build an A-Frame Picnic TableWant more wood working projects? Check out these 15 amazing woodworking projects to try.Project PDFsClick the links below to download the materials and cutting lists for this project, as well as Figure A and B.

Figure A & B, Cutting List and Materials List...

Read More →

Disclaimer: images, articles or videos on this website sometimes come from various other media sources. Copyright is fully held by the source. If there are problems related to this, you can contact us on this page.
Bookmark ID: 12595669567

Built to last viking long table is just one of the many collections of bookmark on this website. There are approximately 4687 posts that exist in our database associated with this article. Here are the details of "built to last viking long table" article:

Category:
Title:
Image URL:
Post URL:

This is a article related to built to last viking long table, there are approximately 4687 article related to this woodworking category. Please see the details below and click on the title for more information..

Built To Last Viking Long Table Woodworking 150 x 100

Built To Last Viking Long Table

The Viking TableThis style of viking table is known as a drawbore trestle.The 'trestle' is the stretcher that connects the legs, and 'drawbore' refers to the 'bored' mortises and tenons that 'draw' the legs and trestle tightly together to create a stable base.You can easily shorten (and lighten) your table ... Built to last viking long table is post about Woodworking bookmarked by shawn with ID 12595669567 was uploaded on 29-01-2019 and has been viewed 253,520 times.

A Small Bureau Built To Last Casework 150 x 100

A Small Bureau Built To Last

Synopsis: Tapered sliding half-dovetails lock the top to the sides, half-blind dovetails join the drawers, and all the dovetails work together to make a rock-solid small chest of drawers.Moldings hide its joinery and an opaque painted finish complete this 18th century-looking small chest.The author takes you through the building process ... A small bureau built to last is article about Casework bookmarked by michael with ID 11140063305 was uploaded on 04-01-2019 and has been viewed 410,998 times.

Cut Long Sliding Dovetail Jobs Down To Size Woodworking How To 150 x 100

Cut Long Sliding Dovetail Jobs Down To Size

Sliding dovetails, like those you might cut into the ends of a shelf 12" wide or wider, can produce so much friction during glue-up and assembly that they catch in the dovetail slot Cut long sliding dovetail jobs down to size is post about Woodworking How To bookmarked by alexander with ID 12815528761 was uploaded on 03-01-2019 and has been viewed 36,737 times.

Raise The Table To Cut Super Thin Materials Woodworking How To 150 x 100
Raise The Table To Cut Super Thin Materials

Recently, I was making wooden chests for my young daughters and decided to use brass accent strips for edging Raise the table to cut super thin materials is article about Woodworking How To bookmarked by chad with ID 11077859800 was uploaded on 24-01-2019 and has been viewed 294,049 times.

Table Rout Long Workpieces Crown Down Woodworking How To 150 x 100
Table Rout Long Workpieces Crown Down

When molding long workpieces on a router table, the workpiece must be held flat against the table and fence in order for the router bit to cut a consistent, smooth profile Table rout long workpieces crown down is bookmark about Woodworking How To bookmarked by alfredo with ID 13779593642 was uploaded on 12-02-2019 and has been viewed 82,467 times.

To Joint Long Pieces Of Material Tune In To J Channel Woodworking How To 150 x 100

To Joint Long Pieces Of Material Tune In To J ...

I needed to put a nice straight edge on a long piece of stock, but because the piece was longer than my jointer's tables, I wasn't having much luck To joint long pieces of material tune in to j channel is post about Woodworking How To bookmarked by jay with ID 12083123531 was uploaded on 02-01-2019 and has been viewed 402,868 times.

10 Seconds To A Dead Square Drill Press Table Woodworking How To 150 x 100

10 Seconds To A Dead Square Drill Press Table

Magnetic digital angle gauges, that work so well for setting a tablesaw's blade angle, make easy work of adjusting a drill-press table square to its chuck 10 seconds to a dead square drill press table is bookmark about Woodworking How To bookmarked by lewis with ID 13191765439 was uploaded on 25-01-2019 and has been viewed 107,419 times.

Open The Door To A Quick Flat Assembly Table Woodworking How To 150 x 100

Open The Door To A Quick Flat Assembly Table

Flat, square projects start with a flat worksurface.Make one by laying a door across two sawhorses.A hollow-core door is stiff and flat, yet light enough that one person can lift it easily.And it stores flat against a wall.Check for a slightly damaged door at a home center—it will serve well ... Open the door to a quick flat assembly table is article about Woodworking How To bookmarked by jared with ID 11717659295 was uploaded on 15-01-2019 and has been viewed 257,105 times.

Heritage Project The Shaker Communities Reached Their Height During The 1800 S But The Last Remaining Community At Sabbathday Lake Maine Still Carries On To This Day They Are Most Well Known For The Enduring Legacy Of The Shaker Furniture Style Simple And Unadorned In Appearance It Was Built With A High Degree Of Craftsmanship With Individual Craftsmen Developing Their Own Discrete Ornamentation To Set Their Pieces Apart From The Others As The 1800 S Drew To A Close The Shaker Style Started To Adopt Some Of The Ornamentation Of The New Victorian Era Magazine 150 x 100

Heritage Project The Shaker Communities Reached Their Height During The ...

Shaker Wall Clock Illustration by Mike Del Rizzo This Shaker wall clock is based on a series of clocks that Isaac Newton Young started in the spring of 1840.While this clock doesn't stray too far from those built by Young in terms of its overall design, I've made some changes ... Heritage project the shaker communities reached their height during the 1800 s but the last remaining community at sabbathday lake maine still carries on to this day they are most well known for the enduring legacy of the shaker furniture style simple and unadorned in appearance it was built with a high degree of craftsmanship with individual craftsmen developing their own discrete ornamentation to set their pieces apart from the others as the 1800 s drew to a close the shaker style started to adopt some of the ornamentation of the new victorian era is post about Magazine bookmarked by marshall with ID 12768860253 was uploaded on 13-03-2019 and has been viewed 192,790 times.

Shop Project This Router Table Was Built 20 Years Ago And Has Stood The Test Of Time Although Over The Years A Few Minor Shortcomings Have Been Realized Learn How The Original Was Built And How To Tweak A New Build So It S Virtually Perfect Magazine 150 x 100
Shop Project This Router Table Was Built 20 Years Ago ...

The Ultimate Router Table Revisited Photos by Rob BrownIllustration by Len Churchill When I designed it, I wanted to incorporate as much storage into the router table as possible so I added two banks of four drawers, as well as the larger storage underneath the drawers.I have used this router ... Shop project this router table was built 20 years ago and has stood the test of time although over the years a few minor shortcomings have been realized learn how the original was built and how to tweak a new build so it s virtually perfect is post about Magazine bookmarked by craig with ID 11170045500 was uploaded on 28-04-2019 and has been viewed 29,228 times.

Top Ten The Table Saw Is A Very Common Machine Mainly Because It Can Do So Many Operations In A Shop Adding To Last Issue S Top 10 List Here Are 10 More Tips On How To Safely And Productively Use Your Table Saw Magazine 150 x 100
Top Ten The Table Saw Is A Very Common Machine ...

Tips on How to Better Use a Table Saw - Part 2 Photo by Rob Brown 1.Clear the AreaCutting an 8'-long sheet on a table saw requires at least 8' behind the blade and over 8' in front of the blade to be clear of obstructions to be able to ... Top ten the table saw is a very common machine mainly because it can do so many operations in a shop adding to last issue s top 10 list here are 10 more tips on how to safely and productively use your table saw is post about Magazine bookmarked by max with ID 1343185517 was uploaded on 12-03-2019 and has been viewed 14,352 times.